Golden-lighting 1208-3P DNI Manuel d'utilisateur télécharger pdf

Assembly Instructions: 1208-3P DNI (Marcellis)

IMPORTANT:

• ALL INSTALLATION WORK SHOULD BE DONE BY ACCREDITED PROFESSIONAL.

• SHUT OFF POWER SUPPLY AT FUSE OR CIRCUIT BREAKER!

• USE ONLY THE SPECIFIED BULBS. DO NOT EXCEED THE MAXIMUM WATTAGE!

PREPARING FOR INSTALLATION

Carefully remove all of the contents from the carton. See the

important notes above. Shut off the power at the circuit breaker

andcompletelyremovetheoldxturefromthewall,including

theoldmountingstrap.

Fromthepartsbagremovethemountingstrapassembly.One

endofnipple(F)shouldbeattachedtomountingstrap(A)with

washerandhexnuts(C&D)inplace.Theotherendshouldhave

canopy loop (H) attached.

Attachmountingstrap(A)tothejunctionboxusingmounting

screws(B)andascrewdriver.Tightensecurely.Unscrewcanopy

loop collar (I) from canopy loop (H). Pass canopy (G) over the

mountedcanopylooptotesttheheight.Approximatelyhalf

ofthecanopyloop’sexteriorthreadsshouldbeexposed,and

thecanopyloopcollarshouldtsnuglyontothecanopyloop.

Removecanopy(G)andadjusttheheightofnipple(F)and

canopyloop(H)untilthedesiredheightisreached.

Bymeasuring,determinethecorrectamountofchainandwire

neededforproperhangingheight.Ifnecessary,useapairof

plierstoopenandremoveanyexcesschain.Attachoneofchain

connectors(K)toeachendofchain(J).Passthexturewires

throughtoploop(H).Attachoneendofchain(J)totoploop(L)

usingchainconnector(K)andclosechainconnector(K).Attach

oneendofeachrod(O)todecorativehooks(N)onxturebody

(P). Use the free end of rod (O) to attach the rod to the hooks on

top cap (M). Use the free chain connector (K) to attach chain (J)

tocanopyloop(H).Feedthexturewiresupthroughthechain

(everythreelinksorso),pullingthewiresuntiltaut.Trimthewires

tothedesiredlengthplus8to10inches.

CONNECTING THE WIRES

Haveanassistantsupportthextureweightwhilecompleting

thewiring.Threadthexturewiresthroughcanopy(G).Attach

thexture’swirestothepowersupplywiresfromthejunction

box.Connectblacktoblack(orsmooth);whitetowhite(or

ribbed);groundtoground(greenorcopper).Twisttheendsof

thewirepairstogether,thentwistonawireconnector.Make

surealltwistsareinthesamedirection.Ifthereisnogroundwire

(greenorcopper)fromthejunctionbox,locategroundscrew(E)

onmountingstrap(B)andwrapthexturegroundwirearound

thegreengroundscrew(E).Useascrewdrivertosecureground

screw(E)ontothemountingbracket.Tuckallwiresneatlyinto

thejunctionbox.

FINISHING THE INSTALLATION

Note: Completetheremainingstepsafterthextureishung.

Tightenthedecorativehammerednials(T)ontothethreadsat

thebottomofthexturearms.

Carefullyslideglassshades(Q)oversockets(S).Candlesleeves

(R)haveretainingringsattached.Eachretainingringhastwo

smallholesineachside.Theglassshadeopeningistight.

Carefullypushthecandlesleevesdownintotheglassshades

and over the sockets. Carefully place the tips of socket tool (U)

intotheholesintheretainingring.Usesockettool(U)tothread

theretainingringsontothesocketthreads.Thiswillsecurethe

glassinplace.

Installlightbulbsinaccordancewiththexture’sspecications.

Donotexceedthemaximumrecommendedwattage.

Your installation is now complete. Turn on the power and test the

xture.

CLEANING TIPS

Treat the xture gently! Regular cleaning will reduce the need for deep cleaning. For regular cleaning, turn off the light and wipe down the

xture with a clean lint-free cotton or microber cloth. Never spray cleaner directly onto the xture.

For Customer Service, contact

the place of purchase to arrange

for replacement parts.

BLACK

(Hot)

WHITE

(Neutral)

GREEN

(Ground)

HOUSE WIRES

SMOOTH

(Or Black)

FIXTURE WIRES

RIBBED

(Or White)

BARE COPPER

(Or Green)

Résumé du contenu

Page 1 - FINISHING THE INSTALLATION

Assembly Instructions: 1208-3P DNI (Marcellis)IMPORTANT: • ALL INSTALLATION WORK SHOULD BE DONE BY ACCREDITED PROFESSIONAL. • SHUT OFF POWER SUPPLY

Commentaires sur ces manuels

Pas de commentaire

Golden-lighting 1208-3P DNI Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Éclairage Golden-lighting 1208-3P DNI. Golden Lighting 1208-3P DNI User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Éclairage Golden-lighting 1208-3P DNI